New on LowEndTalk? Please Register and read our Community Rules.
All new Registrations are manually reviewed and approved, so a short delay after registration may occur before your account becomes active.
All new Registrations are manually reviewed and approved, so a short delay after registration may occur before your account becomes active.
kloxo no ip address problem
hi
I am using kvm (leaseweb) virual server.i have installed kloxo 6.1.19 panel.but I am unable to add Dns templete.I get an error like 'Alert: no_ip_address'.
u can check screen shot
http://oi57.tinypic.com/1zpl9ie.jpg
plzz tell me solution guys
Comments
Usually this issue related to your IP declare as 'bootproto=dhcp' instead 'bootproto=static' in ifcfg-eth0.
Appear on Kloxo Official 6.1.x or Kloxo-MR 6.5.0. Kloxo-MR 7.0.0 already accept for 'bootproto=dhcp'.
What should I do? If I take another location and change ip .So these problems will be over
Correct me if I'm wrong, but isn't it possible your service does not have any free IPv4s? Kloxo pings prior setup and if it's already used, you'll get that message. Chances are, you have only 1 IPv4 in your account and you are trying to reuse it. Right?
i want to know is it my ip problem or not .if yes then i will change my server
Find out /etc/sysconfig/network-scripts/ifcfg-eth0 to know using 'bootproto=dhcp' or 'bootproto=static'.
i found out
[root@LFDt001 ~]# /etc/sysconfig/network-scripts/ifcfg-eth0
-bash: /etc/sysconfig/network-scripts/ifcfg-eth0: Permission denied
[root@LFDt001 ~]#
Try 'cat /etc/sysconfig/network-scripts/ifcfg-eth0'
i found
[root@LFDt001 ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0
Virtio Network Device
DEVICE=eth0
BOOTPROTO=dhcp
ONBOOT=yes
[root@LFDt001 ~]#
The answer is:
ask to provider to know how to change 'BOOTPROTO=dhcp' to 'BOOTPROTO=static'. Remember, 'BOOTPROTO=static' need to know IP address, gateway and netmask
Update or reinstall to Kloxo-MR 7.0.0 (read https://github.com/mustafaramadhan/kloxo/blob/dev/how-to-install.txt)
thank you bro
i have sended support ticket.
IF it doesn't work out, just order an extra IPv4
Try to add to /etc/sysconfig/network-scripts/ifcfg-eth0 in new line the:
IPADDR=123.456.78.89 ---change the numbers to your vps IP adress.
this command not working /etc/sysconfig/network-scripts/ifcfg-eth0
i found /etc/sysconfig/network-scripts/ifcfg-eth0 -bash: /etc/sysconfig/network-scripts/ifcfg-eth0: Permission denied [root@LFDt001 ~]#
its permission denied
my extra ip are here
Gateway
37.48.120.126
Mask
255.255.255.128
i dont know why I have this problem
Just stick with what mustafaramadhan said. He know how Kloxo (MR) work here more than anyone I believe.
The major problem faced now is that network configuration cannot be changed.
You should see the new IP in Kloxo cp, just add accordingly.
So, must to open the file, and add your IP in new line with 2 step :
nano /etc/sysconfig/network-scripts/ifcfg-eth0 ---- /***with nano command you can open it, or open with the file with filemanager ***
IPADDR=123.456.78.89 -----/*** this is a new line with your IP to add to */etc/sysconfig/network-scripts/ifcfg-eth0 * file
i need manual static network config for centos 5.if knw anybody then post here
?
With assumption 37.48.120.126 as GATEWAY and 255.255.255.128 as NETMASK, Change XYZ in 37.48.120.XYZ
Can kloxo be installed on centos 7? or debian 7?
Centos 5
/etc/sysconfig/network-scripts/ifcfg-eth0
see the field DEVICE:
if DEVICE=eth4, not eth0
Please copy file ifcfg-eth0 to ifcfg-eth4 and check following fields:
DEVICE=eth4
BOOTPROTO=static
IPV6INIT=yes
IPV6_AUTOCONF=yes
IPADDR=130.77.88.99
NETMARSK=255.255.255.192
GATEWAY=130.77.88.1
reboot system
Go to admin — Servers — localhost — {IP Addresses}
if you didn't see the line:
eth4___localhost static 130.77.88.99 255.255.255.192 130.77.88.1 Ethernet localhost
click "Re Read IPaddress" and check again.
If it's not work.
service network restart
service kloxo restart
check IP again.
@homecat old topic m8, but using the Kloxo admin page to manage IP's has worked better for me.
wow still get replies for this thread?