All new Registrations are manually reviewed and approved, so a short delay after registration may occur before your account becomes active.
Help setting up IPv6 on BuyVM
Hi guys,
I was wondering if someone who has BuyVM could tell me what I'm doing wrong. I've never been able to figure out the proper method to enable an IPV6 address on Debian 10, so I've just been using v4 only. I figured that while I'm setting up a new VM, I'd give it another go.
These are the steps I've taken:
1. I went to BuyVM's Stallion control panel and added a new IPv6 address. I just put random digits in each box, since I don't really care what the address is.
2. I edited my interfaces file, and created a file for the interface at /etc/network/interfaces.d. This is my interfaces file, and this is my eth0 file.
After restarting the VM, I'm unable to ping Google over IPv6. I get a destination unreachable error. Does anyone know what I've done wrong?
Thanks.
Comments
Shouldn't you contact buyvm support instead ?
Try adding these in your
interfaces
file.I figure it isn't really a BuyVM issue, more that I'm doing something incorrectly.
Thanks, I'll give it a go.
its complicated for majority of people and this is a reason why they do prefer the LET Helpdesk!
Seriously?
https://www.lowendtalk.com/discussion/167510/how-does-netcup-delivery-works
https://www.lowendtalk.com/discussion/166114/what-happened-to-soyoustart-arm-storage-servers
https://www.lowendtalk.com/discussion/164763/how-to-whitelist-ip-from-ovh-anti-ddos
https://www.lowendtalk.com/discussion/163821/ovh-delivery-time
https://www.lowendtalk.com/discussion/162932/buyvm-net-down
https://www.lowendtalk.com/discussion/163213/hostsolutions-down
What ?
Since buyvm support is good why shouldn't he contact them ?
If you contact ovh support you will receive a response in 1 week if you are lucky
Well, like most providers here, BuyVM sell unmanaged VPSes, and so the question of how to set up IPv6 on the OS of one's VPS isn't covered by support, at least not normally.
It would be a different question if IPv6 wasn't working at the network level, in which case it would be something that only BuyVM could address.
Assuming that BuyVM have set up their KVM templates properly for IPv6, you could first install a Debian template and save a copy of the network settings and then use these settings when you install from an ISO. In general, this is a good strategy to follow.
(But I can't confirm that BuyVM have set up their KVM templates properly for IPv6.)
What does this mean? Are the IP's not just assigned to you?
Dude, he didn't grok you were using variables he needed to replace (tip: use $'s, not that he'd grok, either, but maybe).
Needs more hand holding...
You can't use just random stuff for IPv6, they must have provided you some IPv6 or IPv6 range, you to use that. You also need to add that IP in your OS.
Oh well, I tried.
Hope he managed 😄
IIRC you get a /64 subnet and you then have to manually add a (or many) IPs.
Why you would enter random numbers instead of just putting a 1 in the last box is a mystery to me though.
You can check what IPs are assigned with
ip -6 a
and the routes withip -6 r
Ticket and ill help we always do as best we can to help.
Francisco
I also had difficulty setting up ipv6 on buyvm vps. While this is not clearly documented on the wiki page. A ticket asking about how to set up IPv6 on vps at BuyVM will be responded quick well. So is covered by support and their staff will help you to set on your vps.
Okay, good to know.
Nevertheless, in general, a customer shouldn't automatically assume that a provider's support will help them set up IPv6 on the OS of their unmanaged VPS.