All new Registrations are manually reviewed and approved, so a short delay after registration may occur before your account becomes active.
Adding IP blocks on proxmox on single hardware MAC
Hi,
We are new to the proxmox. We need to add two IP Block ranges on the server. But we don't have individual mac address for each IP's. We only have the main hardware mac. How can we add those IP blocks to proxmox and get it work?
142.xx.xx.xx/29
208.xx.xx.xx/27
root@s100382:~# ifconfig
eth1 Link encap:Ethernet HWaddr 9x:xx:ba:xx:f2:xx
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2261370 errors:0 dropped:0 overruns:0 frame:0
TX packets:258799 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:179678029 (171.3 MiB) TX bytes:80871738 (77.1 MiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:90275 errors:0 dropped:0 overruns:0 frame:0
TX packets:90275 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:19027723 (18.1 MiB) TX bytes:19027723 (18.1 MiB)
tap101i0 Link encap:Ethernet HWaddr ex:xx:xx:xx:7b:xx
UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:1992729 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 
TX bytes:60 (60.0
vmbr0 Link encap:Ethernet HWaddr 9x:xx:ba:xx:f2:xx
inet addr:142.xx.xx.xx Bcast:142.xx.xx.xx Mask:255.xx.255.xx
inet6 addr: fe80::92e2:baff:fe04:f268/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2261328 errors:0 dropped:0 overruns:0 frame:0
TX packets:258059 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:148016857 (141.1 MiB) TX bytes:80824614 (77.0 MiB)
Please help us on this.
Thank you for your help!
Comments
Who is your hosting provider? Providers like OVH and Online.net for example allows creating vMAC's for each IP or attach multiple IP's to a single vMAC. Those vMAC's are then automatically bridged to your dedicated server.
I suppose there are more clean and better ways, but that's at least how I found it easiest to use IP blocks on my proxmox server.
Maybe someone more knowledgeable could share their own methods of doing this.
https://pve.proxmox.com/wiki/Firewall
Hi,
Our provider is nocix..Multiple IP's attached with single mac.
Any steps to add this.
Thank you!
You forgot
On a more serious note, did you open a ticket with Nocix? I'm sure they could help you on this.
Hi,
Yes we did. But they won't help us.
They asked to refer forums.
https://www.ubiquityhosting.com/blog/configure-ip-addresses-debian-and-ubuntu-tutorial/