All new Registrations are manually reviewed and approved, so a short delay after registration may occur before your account becomes active.
Anyone used vrack at OVH?
Hello,
I'm trying to set vrack 1.5 on OVH but seems there is issue with it.
I have followed http://help.ovh.com/VrackInfrastructureServer but vrack keep getting disconnected and timeout.
Vrack is used for OpenVZ
This is my setup
ifcfg-eth1
BOOTPROTO=static
>
IPADDR=xxx.xx.xxx.169
>
NETMASK=255.255.255.248
>
ONBOOT=yes
>
BROADCAST=xxx.xx.xxx.175
>
DEVICE=eth1
rule-eth1
from xxx.xx.xxx.168/29 table 125
route-eth1
default via xxx.xx.xxx.175 dev eth1 table 125
And for eth1:0 I have up to eth1:2
BOOTPROTO=static
>
IPADDR=xx.xxx.xx.176
>
NETMASK=255.255.255.240
ONBOOT=yes
BROADCAST=xx.xxx.xx.xxx
And set all the same for route-eth1:0 rule-eth1:0 as before.
The issue is
Reply from xx.xxx.xxx.134: bytes=32 time=37ms TTL=58
>
Reply from xx.xxx.xxx.134: bytes=32 time=35ms TTL=58
>
Request timed out.
>
Request timed out.
>
Request timed out.
>
Request timed out.
>
Request timed out.
>
Request timed out.
>
Request timed out.
>
Reply from xx.xxx.xxx.134: bytes=32 time=35ms TTL=58
>
Reply from xx.xxx.xxx.134: bytes=32 time=34ms TTL=58
>
Reply from xx.xxx.xxx.134: bytes=32 time=42ms TTL=58
Or network goes down and never come back.
I never expected such issues with other DCs so not sure if it's configuration issue or something related to OVH.
Anyone else had such issue with OVH already opend ticket with OVH but that probably will take some time.
Comments
What IP's are you using for the two eth1 interfaces? Are they from an OVH IP block?
Or is one a local IP?
gateway seems to be wrong, should be xxx.xxx.xxx.175 (2nd last IP), broadcast xxx.xxx.xxx.176 (last IP)
routing table in place?
We are using IP blocks from OVH as the OVH tutorial shown.
Haven't really tried with private IPs I will give ago maybe that's the issue I skipped.
I have changed moment ago to 174 from 175 to test but gives same results with timeout.
routing table in place? can you ping the gateway .175?
Yes I can Ping gateway as ping is back right now.
I have set eth1 as local for vrack atm ping seems to be back.
Normally it goes down after 6 hours so I will monitor it right now.
Thanks for help everyone I will let in next 6 hours if new config is working
Hmm still vrack getting disconnected and timeout even with local connection. Looks like vrack issue as now can't get Ping back at all with same settings also nothing was changed from last 12 hours.
Id suggest to test if vRACK issue or config issue.
Create a eth1 network device with the following :
DEVICE=eth1
BOOTPROTO=static
IPADDR=172.16.0.10
NETMASK=255.240.0.0
ONBOOT=yes
Removing any other network config apart from the standard eth0.
If you then have another server on vRACK (I guess the point of having this server on vRACK), setup this with the same config apart from .11
Then test if you can keep a ping running between the two servers, if this does not drop then the issue is with your config when you are then using an IPBlock.
Stupid question but you have moved the IP Block to the vRACK in question?
Sadly I have only x1 Server which support Vrack, My clients requires more IPs so vrack is required in this cause.
IPs and server are moved in Ovh manager in Network settings.
But it strange network was working non stop 4 h and than disconnected with no reason now ping is back for few sec and again same happens.
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
Probably best would be call OVH tomorrow at 9am let their tech look into this as if network works sometimes config seems to be fine just connection is lost from vrack
Also on ifconfig eth1
There seems some errors so I will look into this now.
Feel free to PM me all your config files and I will give a quick check over them make sure nothing obvious before you chase OVH further.
did you setup "table 125"?
We did, AshleyUk give us new way to do it atm we working to make it working so far we got gateway ping working we trying to make OpenVZ VPS working now on this network
Seems like OVH Vrack don't support OpenVZ network with venet
is your ovz node setup in vrack?
It was originally installed with eth0 after we are trying to add vrack but seems not working can't find solution on google either
vrack works with any NIC including dummy
Never got it working for me either.
Seems we got it working.
We have set in vz.conf eth1 as main Interface and restarted the vz
Also added
to sysctl.conf
We will monitor it for next 6 h if it will go down or not.
Did say in my PM you need to set eth1 as the main interface for openvz, as you have no routes you need to force traffic down the vRack port.
Glad you have it working.
Thanks
We still using the assign IP method eth1:xx as other method with local IP don't work.
We will see if its fixed as normally vrack goes down after 4h sometime after few seconds we are monitoring atm but hope that was the issue and its fixed
Still vrack disconnected with no reason I will call OVH today about it.